duro
Description
The block bonding press duro has been designed for rough duty. Its welded
frame is of correspondingly robust construction, so that the press is equally
suitable for bonding panels, medium-sized blocks, and for lamination work. The
four pressure beams, each fitted with a dual-acting hydraulic cylinder for
pressures up to 35.000 N, provide the necessary force over the entire workpiece
width. This also applies for self-locking profiles.
The hydraulic pressure cylinders have a stroke of 200 mm. This enables tongue
& groove profiles to be glued in a single operation.
Operation is extremely simple, whereby a complete working cycle is controlled by
means of just three push-buttons: "Press", "Stop", and
"Release".
Working height and adaptation to workpiece size are easily adjustable via the
indexing grid with hole spacing of 50 and 100 mm. This ensures optimum settings
and ideal working conditions for the operator, regardless of the task. The
workpiece clamp provides the necessary working safety.
Block Bonding Press duro with one optional pressure beam.
No instruction
No previous knowledge is required for installing and operating the block bonding
press duro. The machine only needs a connection to a power outlet, and is ready
for operation via the three push-buttons and/or a group function.
No installation
The press is simply unloaded and put in the required place, where it is levelled
out by means of the set-screws in the base. Insert the power plug into the
socket (400 VAC). Finished. A compressed air connection is only necessary with
pneumatically-operated clamps.
No servicing
The press is designed and built for practically wear-free operation. Should any
of the working parts become damaged or need replacement after expiry of the
guarantee period, proceed as follows:
- Smooth-running bearings
of the pressure beams
Release the through-bolt and retainer, and exchange the bearing (occurrence: unlikely). - Hydraulic pump
Disconnect power supply. Remove the two pressure lines, unmount the motor and replace (occurrence: unlikely). - Hydraulic pressure cylinder
Should one of the pressure cylinders develop
a leak, unscrew the pressure connection and replace the cylinder (occurrence: very seldom, less than 1%).
In the unlikely event that a pressure cylinder needs replacement, you have two options:
- You order a new pressure cylinder.
- You return the defective cylinder to us,
and we will refund 50% on the purchase price of the new unit.
In both cases, shipment is within 24 hours, and according to your instructions.
Basic set-up
- Operation via three push-buttons:
"Press","Stop", and "Release". - Hydraulic pressure up to 180 bar.
- Safety circuit.
- Operating pressure adjustable
from 40 to 180 bar. - Fully automatic pressure monitoring with
pressure switch. - Smooth-running pressure beams with a
working height of 1500 mm and dual-acting hydraulic pressure cylinders, quick-adjust system, 35.000 N force with 180 bar pressure,
200 mm stroke. - Guide rails with integrated falling latchpins.
- Hydraulic pressure cylinders and guide rails with 50 and 100 mm indexing holes for quick adjustment.
- Depth of pressure plates and guide rails
100 mm. - Pressure cylinders 2 and 3 with safety shut-off valve.
- One spindle-operated workpiece clamp.
Technical data
Construction
Heavy-duty, welded frame construction. The operating panel and the hydraulic
pump unit are firmly mounted to the frame. The pressure beams can be moved along
the entire working width.
Working area
Width: 3000 mm; Height: 1500 mm.
Overall dimensions
Width: 3200 mm; Height: 2400 mm;
Depth: 1200 mm.
Machine weight
720 kg, including the three pressure beams with one workpiece clamp.
Surface finish
Lacquered coating with two-stage finish.
Structured lacquer
RAL 9002 grey-white
RAL 7002 umber-grey
RAL 3020 traffic-red
partially with zinc plating and/or powder coating.
Electrical power supply
1,5 kW, 400 VAC, 3/N, PE, 50 Hz.
Hydraulic pressure
Continuously adjustable 40 to 180 bar.
Features
The block bonding press duro has a rugged construction. All working parts have
been built for continuous, wear-free operation. Operation is extremely simple,
with just three push-buttons. Working height and adaptation to workpiece size
are easily adjustable via indexing holes for the hydraulic pressure cylinders
and the guide rails. This ensures ideal working conditions for the operator. The
pressure monitoring system is fully automatic and maintains the working pressure
at the preset value. Operation can hardly be simpler.
Guarantee
Three years.
Price
asalo block bonding press duro.
Working width 3000 mm, electro-hydraulic, fitted with 3 pressure beams and 1
workpiece clamp.
€ 15.350
Includes packaging, free delivery to a German
border or fob German seaport, and full insurance up to the installation site.
Accessories
for extensions to the initial system:
- pressure beam € 1.900
- workpiece clamp € 470
- swiveling pressure plate € 210
Prices are subject to VAT.
We reserve the right to make changes for technical or economic development reasons.
